Z Probe not working with G30
Hi, Sorry for starting a new discussion, but I have not seen a solution to my issue. I have been struggling with this for over a week and would really appreciate some help.I have a home built CNC...
View Article0922 Temp Sensor Defect error
I installed 0922,with same settings at my 092. Now I get temp sensor defect error at 130C. If I load 092 back, everything is fine.Anyone have this problem?
View ArticleFirmware settings for SD card
We are running a large reprap directly from Repetier on a Mac laptop through the control box they supplied. We have never used the SD card input, control box does not recognize cards.Company that made...
View Articleserial com error system io ports
Hello I started to use reptier firmware just since now and i used the setup guide for the firmware (which is gr8 btw!). I used all the values from my marlin setup to start with (esteps and such) and...
View ArticleMachine freezes after autolevel in 0.92.2
Hello Repetier,I installed 0.92.2 on my CNC router recently, and after G30/G32 it takes the probe(s), returns to the initial position and stops recieving any commands. Only Emergency stop resets the...
View ArticleMax PWM in vers 0.92
I a trying to configure the firmware settings for my pibot vers1.4 board with vers 0.92 and noticed that the max PWM setting for the extruder under the temperature menu is no longer there. For the...
View ArticleZ-Speed too slow
Hello,I have an Mendel Max printer with dual extruderI uploaded the current repetier firmware, everything works but the z-speed. its extemely slow, and the step are wrong i think. (insetead of 10mm,...
View ArticleBed leveling - can't get nozzle close enough to bed surface
Hi,I have a problem getting the nozzle close enough to the bed after bed leveling.My configuration: Velleman K8200, Rumba board (80), Repetier firmware 0.9.3, inductive sensor mounted near hotend, no...
View ArticleRamp 1.4
I have tested all the motors and the heater with this code and it's working: http://reprap.org/wiki/RAMPS_1.4#RAMPS_1.4_test_codeWith Repetier software evrything works exept the extruder motor.Did I...
View ArticleZ-homing no endstop hit
Hi,after installing the Repetier firmware 0.9.2 to my RUMBA board I had the following problem:X and Y homing work fine, as expected. In Z - homing the printhead only moves a short distance (about 5 mm)...
View Articlev0.92 too big for Gen6 (ATmega644p)
When compiling v0.92 for my gen6 board I get a too big error (about 68KB).Am I doing something wrong or does v0.92 not support 644p based boards?Thanks
View ArticleHoming issue on custom Delta build
Hello,I have a really strange behavior, both on the latest 9.2 and also 9.1.8When hitting the home button, X axis gos up, hits the end stop and all works well.But Y and Z axis act randomly.sometimes...
View ArticlePibot 2.0
Are there any plans to make the firmware compatible with pibot vers 2.0 in future?
View ArticleDelta printer phisical Dimensions
Hello, I need some help with delta configuration please. That is the manning of "Floorsafety margin"? Where in the firmware this number is used? If I want to use Z probing and Z correction, is it...
View ArticleRepetier-Firmware configuration tool
Repetier-Firmware configuration tool doesn't display the window where you can check the printing time and filament printed quantity, but when I upload the firmware at the arduino ide to the motherboard...
View ArticleProblems with Smart LCD & Repetier firmware
Hope there's help out there?I've built my 10th Delta printer, all previous ones run on Marlin FirmwareNo problems at all BUT my latest delta I want to run with Repetier firmware...Everything works fine...
View ArticleCompile issue 140215 13:15 GMT
Just downloaded latest firmware to give auto level a go again.But getting compile issues, the website version of the firmware is this linked to dev firmware or stable? as i seem to have compile issues...
View ArticleHey guyss ı very need your helps
I complied the code after that ı get some errors , please help mee !! ui.cpp: In member function 'void UIDisplay::adjustMenuPos()':ui.cpp:2016:47: error: ISO C++ forbids declaration of 'type name'...
View ArticleNeed help getting Repetier Firmware to compile...
Hi All,Okay this is probably super simple but I am having a hard time getting things to compile using the Arduino IDE.I downloaded and installed the Arduino IDE app for my Mac (OS X 10.10.3)I have a...
View Articlez- axis motor.. parameters
Hi huysAfter succesful installation of the firmware in mu newly built 3D printer, I noticed a problem with z-axis: no matter what number for steps/mm I place in configuration.h, the result is alwas...
View Article/pic9814888.png)
/fit-in/580x348/filters:format(webp)/english-betterindia/media/media_files/2026/09/17/balaghat-4-2026-09-17-19-01-31.png)
