Bed unlevel but height map says otherwise?????
Hi GuysIm getting an uneven bed even when using auto level and z correction!if you have a look at the pics below you can see height map shows a good bed but when printing its way out and digging into...
View Article0.92 does not work with Printrboard RevF4
I flased my Printrboard RevF4 with the new Firmware Version 0.92 to be able to change the motor current settings. I´m able to connect to the board but it wont do any movement. I had Firmware Version...
View ArticleRepetier firmware excluding temperature sensors.
Good MorningLoad Repetier firmware on hardware without hotend and without hot.I can not understand how to exclude the temperature sensors.Thank youSandro
View Article0.92.3 Ultimaker-Smartcontroller Combo not Functional
I did a sanity check on a GT2560 (Ultimaker 1.5.7 Compatible) and Smartcontroller LCD 2004 using the Arduino Example LCD Display sketch, using the following pins, and it worked fine.LiquidCrystal...
View ArticleG30 doesnt stop when triggered
Hello, I recently tried configuring Z probe on Repetier firmware 0.92 and I got to a point when the documentation on the official site says : enter G30, the extruder will decrease and when I push the...
View Articleservo wont move with auto bed leveling
i used firmware tool 0.92 as 0.91 does not have 12864 lcd screen.trying to get auto bed leveling working,conected the servo to pwr pins...+,_ and pin 6, tried many servos, wont will respond with g code...
View ArticleDelta Homing issue. Error:A hit floor
Hi, I am not sure if the issue I have is a firmware or host issue, so I apologise if I have this in the wrong category. I have successfully used Repetier before with a print head mounted on my CNC...
View ArticleCoreXY limited movements.
I am currently building a 3D printer, I'm using the system moves "core XY". I'm working with repetier-firmware and repetier-host. When the dimensions of the printer is set from the configuration tool...
View Articleprusa i3 calibration x,y,z
i have a prusa i3, used the calculator for calibration and gotResultResolutionTeethStep angleSteppingBelt80.00 Click to Share!12.5micron201.8°1/16th2mmwhich is fine but which file and where do i enter...
View Articledo i need to install repetier firmware to use on linux with mini fabricator...
do i need to install repetier firmware to use on linux with mini fabricator tiny boy?if so how do i install the firmware?
View Articleautoleveling delta
Hi,I am trying to get the autolevelling working.I am using firmware 0.92 have a delta and a mechanical endswitch installed as a probe.When i check the probe with the G31 command i get L when not...
View Articlead595 thermocouple on RADDS which pin (5V input needed)
Hi,I am trying to connect a thermocouple to the RADDS via an external thermocouple extension board. ( http://reprap.org/wiki/ExtThermoCouple_1.0) I found some info about some other extension boards and...
View ArticleSD Card Reader Setup
Hi all,Can't seem to get my SD card reader to function, this is the code in Repeteir Firmware Configuration H:#ifndef SDSUPPORT // Some boards have sd support on board. These define the values already...
View Article0.92.3 Ultimaker-Smartcontroller 2004 and 12864 Now Working, but...
The SmartController 2004 is working, but a few characters glitch from time to time. Otherwise, it works fine.The SmartController 12864 full graphical display works even better. No glitches at all. Only...
View ArticleMax endstop homing order.
I'm not sure what to label the max endstop as. My goal is to make the order look like this.1. Z Max2. X Min3. Y Min4. Z MinIs this possible?#define HOMING_ORDER HOME_ORDER_XYZ
View ArticleNo beep sound on lcd controller
I have the reprapdiscount full graphic smart controller and I have the beep sound enabled when the encoder selector is turned but mine doesn't sound, is it broken?
View ArticleFlashing a Da Vinchi 2.0 Duo
Hi folks,As a last-ditch effort to avoid old-yellering my Da Vinci 2.0 Duo, I thought I'd try flashing the firmware. I like the notion of the configurator you folks have come up with, but I don't know...
View ArticleConfiguring print fan pin on Sanguinololu
Hello all,I've got a Sanguinololu v1.3a + Panelolu2 LCD where the fan is connected to pin 5 on the ATMEGA 1284P (PB4). How would I configure Repetier firmware v0.91 to control the fan? I've tried...
View Article