TMC2100 drivers with Due/RADDS Dual X Carriage
Is there a problem with Repetier firmware and TMC2100 drivers?Some moves when printing the firmware just causes the stepper to sit in the same location and buzz, then the next moves are normal. Is this...
View ArticleEaglemoss v3 printer firmware
Hi, pleased to have the opportunity to post something and say hello. I own one of the eaglemoss v3 3d printers and after learning about firmware would like to change it from sprinter to repetier, it...
View ArticleHotend Switching Problem
Hi, i switch between two hotends using the Fan2 Signal and a Tool change script in Slicer. However the tool change happens 2 seconds before the layer ends. I checked the G-Code which turned out to be...
View Articlefan control
just built a large delta tested it with marlin everything seams ok --- trying repetier.how do I achieve this :: in repetier.#define CONTROLLERFAN_PIN 8 //Pin used for the fan to cool controller,...
View ArticleRADDS + ReprapDiscount Full GLCD
hiI see it in the online config tool there is an option to use the RRD Full GLCD with RADDS, I have both LCD2004, GLCD 12864 and the RADDS LCD, but I like to use the GLCD instead, do I need to make any...
View ArticleClik here to view.
Nozzle hitting AND lifting off of bed after G33 - Delta
I'm using a He3D K200 Delta with Repetier 0.92.9 FW, and the most recent Repetier Host.I'm following along with this video exactly:I'm making sure that my probe height is correct (1.5mm), and that...
View ArticleFirmware Setup for Fan Extension Board when you are already running 2...
HiI need help configuring the firmware to run 2 object fans. i already have all other outputs maxed out using 2 extruders and a heated bed.so i got the fan extender board, but i can't figure out how to...
View ArticleCompile and debug step by step.
Good morning.Which software is possible use for debug step by step ?It 'very difficult to debug with Arduino IDE.ThanksSandro
View ArticleAuto-leveling works but nozzle hits the bed
I have a cartesian printer, with an inductive sensor and an aluminium bed for z probing. Auto leveling and storing it in eeprom with G32 S2 works in the sense that the Z axis corrects when it moves in...
View ArticleBLTouch von Antclabs
Versuche gerade verzweifelt den BLTouch von Antcalbs zum laufen zu bringen. Unter Marlin soll es einfach sein. Aber mit Marlin habe ich nichts am Hut. Hab mich bisschen in Repetier eingearbeitet für...
View ArticleRepetier-Firmware for XYZPrinting Da Vinci Mini w
Helloi´m searching now some days at the www but i can´t find anything. is it possible to use the Repetier-Firmware at the Da Vinci mini w series?if yes, where can i find the reight version ant a how to...
View ArticleClik here to view.
Layers shifting at random times
Hello.I've thought long and hard about it and i think it's a firmware problem. I've had the same problem with my Micro M3D printer and a new firmware fixed it, so i'm asking for help for my bq Prusa i3...
View ArticleMy stepper motors do not work
So i just downloaded thenrepetier host software/ firmware, and the printer is hooked up to the computer, and i can manually move the printer with the axis buttons, but when i tell the printer to run...
View ArticleZ axis speed
Hi. I cant find the setting to control this behaviour:When I start a print, firts the heated bed starts heating, when it reachs the temp, then a homeing of all axis is triggered_ first X then Y and Z...
View ArticleClik here to view.
Problems to implement custom g-code for Extruder change and z-offset
Hi there,I´m new here and have a big problem with my new self built printer...maybe the reason is because I´m not a software engineer... :-) - mechanical side works perfect so far.The general function...
View ArticleZ won't move after homing with repetier dev
UPDATE 2: I lowered the bed about 2/3rd the way down. then ran G28 Z. My wife then pushed both z min's and the bed homed about half way. She held down the limit switches and I could no longer move...
View ArticleServer PSU wont turn on through Repetier Host
having issues finding the answer to this, currently running a Tevo Tarantula 3D printer with MKS 1.4 board. Firmware I am using is the Repetier FW that is on the FB Tevo group. For some reason I am not...
View ArticleChange jam detection behavior in dev
I'm using jam detection with a microswitch to trigger high when out if filament. It works fine. Bit I don't know that it's out till I look at the printer. Can I modify the gcode so that I can add an...
View ArticleThermistors not working correctly
Good day.I made Ramps-FD V2.B from github https://github.com/bobc/bobc_hardware/tree/master/RAMPS-FD and have a problem with the thermistors. All other works- endstops, stepper drives, heaters. Use...
View ArticleWhen calibrating Z, need to move below 0, how can I?
I am trying to calibrate my Z, and currently Z0 is too high, I want to move it down towards the bed and find the exact amount it is high, but I am guessing software endstop prevents this, even if I set...
View Article