Behaviour of G92
Hi all,Just checking on the seen behaviour of G92 command.As it may make some difference here, my machine uses a Z probe and all triggers are done at their minimum position, so 0.Yesterday I was trying...
View ArticleSpeeds/Size
I want to try out Repetier from Marlin. I have it working it homes controls my printer etc. However the Homing Speed is slower than Marlin. I also tried to print something and the size of the item was...
View ArticleUnderstand dimensions for configuration for delta printer
HiI have build my own delta printer, and I am having problems understanding the dimensions in repetier configurator.There is a picture under dimensions when you use the configuration web tool. On this...
View ArticleResolution setting changes nothing.
Hi, I am a previous user of repetier firmware and have had success with it so I figured I would use it for my new corexy 3d printer. Most things are working perfectly, but there is a big problem: The...
View ArticleClik here to view.
G4 (dwell) causing stuttering motion on delta printer
Hi, I'm trying to improve my printer's behaviour when restarting after retractions. It's a delta with Bowden and the filament takes a bit of time to start flowing properly again after a retraction. I'm...
View ArticleCan I have bending correction with BED_LEVELING_METHOD = 1 and GRID_SIZE = 2 ?
I've read that you can make use of bending correction (ABC) only with the 3 measurement points.But I'd like to confirm if it is exclusive of this method or I can apply it for a grid = 2 (four...
View ArticleUnknown command
I repetier,I have installed last 1.0.0dev version downloaded 18/2/2017 for my mini Kosser with Chimera and autolevelbut when I send M99 X0 from Repetier host I receive continuos message of Unknown...
View ArticleHictop
I uploaded the Repetier firmware to a hictop prusa i3 and the z-axis settings in the old firmware from marlin was #define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,398,94.4962144}398 being the Z axis now...
View Articleafter uploading firmware Z Axis moves very very slowly Hictop Printer
I uploaded the Repetier firmware to a hictop prusa i3 and the z-axis settings in the old firmware from marlin was #define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,398,94.4962144}398 being the Z axis now...
View Articleheater bed not working at all after installing the firmware
after upgrading to Repetier Firmware from Marlin my heated bed will not turn on im not sure what pi i need to useI have a Hictop 3DP17_398 3D Printer and im not really good with this programming thing...
View ArticleG28 Command causes big noise
i have tried all movements X-Y And Z and all now seem fineuntil the bed tries the auto home using G28 x and y seems ok but as soon a Z tries it makes a horrible noise i have to click emergency stopbut...
View Article1mm = 4mm in real world
i have tried various settings and i cant seem to fix my z axisi have tried 300 500 1500 each setting moves my x-axis 4mm when i click the 1 mm movie in manual in repetir host softwarealso when i click...
View ArticleGeeetech G2s print cooling
Hi all,I'm pretty new here but couldn't find anyone with this issue. I have a Geeetech G2S which uses a GT2560 controller which has 4 fan ports. The first is used for the hotend fan, the 2nd is for the...
View ArticleDelta printers. x/y correction
Hi!Recently I´ve a delta printer with no Z probeI have no problem with z height and flatness calibration. At first I make it manually and after I've used escher system with good resultsHowever after...
View ArticleAnet A8, cannot install Firmware
Hi,i have a Anet A8 Printer and i would like to install the Repetier-Firmware because i plan to update the Printer with AutoLeveling.I use the ARDUINO 1.8.1, my Mainboard ist this when i upload the...
View ArticleZ-Probe Homing Issue
I'm using repetier 92.9 with Ramps 1.4.I installed the Z-Probe a little while ago, and it seems like the probing portition is working fine. But when I home the Z axis, it hits the bed, rises a little...
View ArticleAlligator Display problem
Hi Roland,I've an alligator board rev.2 and when I compile with arduino I have these error:'DIOUI_DISPLAY_D5_PIN_PORT' was not declared in this scopeThank you very much for your helpLorenzo
View ArticleUpgraded Firmware, now i have no temperature readings
Hello.I've Just upgraded from 0.82 to 0.92 and am now stuck in a very unusual problem.Both the temperature for my extruder and my heated bed have disappeared. - Both state they are at 0, and turning on...
View ArticleRequest for input on potential firmware configurations for an SLS printer
Greetings, I have been working with FDM printers for over a year now; maintaining converted XYZ daVinci’s, converting a pair of CTC dual extruder MakerBot clones to Repetier firmware on a RAMPS 1.4...
View Article