Enable Z-probing
The sensor is X + 20 away from the extruder. This is the settings I made. I'm getting an error
View ArticleDavinci I.0-A flashing problems
All of the info/videos online I can find are several years old, and I cannot seem to match up the correct versions of firmware with the correct version of arduino vs the correct process.the only...
View ArticleBed-leveling - Probe grinds over surface between measured point
Hello,I tried implementing a 3Dtouch bed level sensor in repetier 0.92.9 and am probing a 4x4 matrix. It does work as expected, the only problem is, that when moving between the points, the probe...
View ArticleMy prints are not centered
Hello,My prints are not centered, they are printing exactly where the Z probe offset is. I have my Z probe at X=32.5 and Y=5 and that is how far the print is from the center.I am using repetier...
View ArticleY stepper has no current till print starts.
I've been using Repetier since 2016 on a homebuilt machine, running very well, using Unipolar steppers on my own driver boards.Recently I decided to go with Bipolar steppers using Polulu A2988...
View Articlez-Correction Enabled....but no working
Hello, I have a delta printer, I am trying to calibrate using the video from the repeater page, the autolevel (G32 S2) does it well, then when I do the height map, and apply G33, it does the distortion...
View Articleassigning pins
Hello,I am trying to use a pin to control a relay with an if/then or while conditional statement. If the extruder is running I want to send a high signal to the relay.So far I have not found any...
View ArticleClik here to view.
UART rx0 tx0 help needed
Hello !I'm using a ramps FD and an ESP3D wired on RX1 TX1I also have a Bigtreetech Touchscreen who also want to use an UART Port. Problem is When i connect the screen to RX0 TX0 it doesn't work... I...
View ArticleKompatibel mit Chiron?
hallo, Ich kämpfe ja aktuell mit Marlin 1.1.9 und meine Anycubic Chiron. Ist denn die Repetier Firmeware mit dem Chiron Kompatibel? Anycubic Chiron Board: TriGorilla Mfg
View ArticleMy he3d ei3 printer bed and nozzle are not heating
I have assembled my printer but it's nozzle and bed are not heating since assembled.i have checked that all the wires are correctly attached.also the light on the board is not glowing when I heat the...
View ArticleLimit Switches and homing switches
I built a 3d printer and fitted one switch either side in max and min positions in the X and Y axis.the idea was to use two of them as reference (homing) and at the same time having over-travel...
View ArticleReduced feedrate on 2nd reference Pass.
The option to reduce the homing feed-rate for 2nd reference Can be set by 1-normal feed rate or 2-To halve the feed rate. What happens if it is made 3 or 4? Will it ignore and home with normal feed?...
View ArticleRecommanded Jerk Acceleration and speed.
I know that these settings are really a minefield in a 3D printer. I have constructed a heavy printer with linear ball guide-ways and heavy duty belts, mechaduino driven steppers. water cooling,...
View ArticleDISPLAY SELECTION
Hello, Is there a way to connect the Duet Panel Due screen to the ramps board and adjust the repetier firmware to use this display?The plugs are similar. Any leads on this???Thanks
View ArticleV2 firmware on MKS rumba32
Good morningThis is the first time I have used Visual Studio Code and Platformie.I have been trying to write V2 firmware to MKS Rumba32 for many days.I get these errors:> Executing task:...
View ArticleDownload Firmware V2 for RUMBA32
I might be stupid, but I cannot find a download for the repetier firmware V2. Where do I get it?
View Articleda vinci 1.0a auto level
When I try to do auto leveling the first point is off the board and fails.
View Article