Solved: Can´t print slow enough
I´ve forgot to change one of the travel accelertions. Now i´m on the way for the slowest printer on earth.---------------------------------------------------------Hello, i´ve got a huge urgent issue....
View ArticleAutolevel bed error
Hi,i've just tried out the 1.0.0dev Version.Now when i try to probe Z and calculate Z Plane i get an error saying:21:41:00.951 : fatal:Could not activate z-probe offset due to coordinate constraints -...
View ArticleDemi Lovato Provides 1st Major Public Performance Since 2018 Overdose At The...
A one hundred and one Information To The Pesach Seder Meal of the vital anticipated performances on the 62nd Annual Grammy Awards was Demi Lovato's comeback performance The singer has been teasing her...
View ArticleSecond Heater Error - Not Heating Up
Hello, I have been having an issue with Repetier Firmware heating the second hotend on my printer. I am getting temperature feedback for both of them. Only the first hotend (T0) will work just fine...
View ArticleFirmware Update without configuration.h
Hi guys,I bought a delta printer 2nd hand and its from a manufacturer that wend out of business a while ago.The printer does not have any "mechanical" means to adjust the bed and I am planning to add a...
View ArticleCord Prolapse And Compression
Sohrabi Davood, M.H. Karimfar and Asadi Fardin, 2007. This is thought more likely to be resulting from prompt diagnosis and administration of cord prolapse, following tips for really helpful practice,...
View ArticleDavici Duo
Hello,i'am new here and my english is not the best. I hope you can understand my problem.I have download the Retier 0.92 for DaVinci 2.0Aby compiling there is an error message:Arduino: 1.5.8 (Windows...
View ArticleHotend not heating
Hello I just mounted an Ulticampy with two hotend and a hotbed. Board : Arduino Mega and Ramps 1.4 The first hotend well work and heat. The hotbed work and heat. Both are well regulated in temperature...
View Article124
The FSAI is monitoring the evolving COVID-19 (coronavirus) outbreak carefully and is following official Government advice. The Chester County Health Department is taking proactive steps to protect the...
View ArticlePrinter slows down a lot for long passes
Hi there. I'm printing with a big (600mm) home made delta printer. Everything works as it should except that for long passes it slows down to a craw.When its printing the infill and the travel distance...
View ArticleSources For Your Neighborhood
As you know, events related to the coronavirus (COVID-19) proceed to impression our nation, Arizona and Peoria. The Walgreens Prescription Financial savings Membership gives reductions on the money...
View ArticlePrinter slows down a lot for long passes
Hi there. I'm printing with a big (600mm) home made delta printer. Everything works as it should except that for long passes it slows down to a craw.When its printing the infill and the travel distance...
View ArticleRPI mit Radds 1.5 und Due, Blobs vermeiden
HalloIch habe das Problem dass mein Core XY Drucker während dem drucken häufig kurze aussetzer hat (0.2s bis 3s), dabei läuft natürlich die Düse aus, und es gibt unschöne Blobs im Druck. Zudem leidet...
View ArticleRADDS with TEMP_GAIN 1 results to BED-Temp always 0.0
Hi,just tried to install dev-version with the new TEMP_GAIN activated. Result was, the Temperature-Reading for the Bed was always 0.0 Degrees and the Bed did not activate. Looking in the Eeprom...
View ArticleLinear Advance - does it make sense using an 8-bit board?
Hi, after updating my Cartesian XY to Firmware V1.0.4,I did first steps with linear advance, but there were no real difference between test pattern lines.Here are some basics:- Rumba board, 8 bit-...
View ArticleMoving from 0.92.9 to 1.0x firmware
Hello I'm disappointed with the 1.0X firmware. My motors are not moving in the right direction since I updated the 0.92.9 firmware on my Sparkcube XL. Specially on the bed levelling... Help Thanks
View ArticleNew Build - Problem getting hotend to heat
Hello,I'm somewhat new to 3D printers, but have built a CNC router before. I am in the process of completing a fairly large 3D printer. It uses the Azteeg X3 Pro printer controller. All of the axes are...
View ArticleThermocouple error
Hello! I have a problem connecting a thermocouple. I use the Ruramps control board. The firmware is configured correctly and works for more than a year, but first I used thermistors. Then a...
View ArticleZ Probe and min Z appear to be mutually exclusive
Hi All,My old printer (my take on a Prusa i3) used Repetier firmware 0.91 on a Sanguinololu board and I never had issues with zeroing out the Z axis despite never having any Z min or max sensors, I...
View ArticleLaser Add-on
i have an engraving laser and i see that you can enable the laser option on the firmware.so am i right in thinking i can have a 3d printer that will also engrave?or is it one or the other.as i have my...
View Article