Speeds changes after firmware modification
HI. I have repetier 0.92 since a while. No problems at all. Today O changed my Z threaded rods to lead screws. So I changed my Z steps in configuration.h. I uploaded the firmware useing the arduino...
View ArticleZ-probe won't home, etc.
I've just brought up 1.0.0dev (previously using .91 without autoleveling compiled in), and am attempting to get an inductive NO Z-probe working. It's wired in parallel with the original Z-min switch...
View ArticlegCode before homing
I'm using 1.0 dev and noticed commits recently allowing us to use a probe as a zmin. This is great! However, I have a BLTouch and need to drop the probe before homing. Is there a "run gcode before...
View ArticleAsking machine about motion status
If you send G1 or any other motion commands those are buffered for good reasons.I'm doing a pick and place machine with 2 board setup and need to know if the machine has reached it's target position...
View ArticleClik here to view.
Print fail detector
Just found the zyyx+ printer and the one thing that caught my attention was the print fail sensor. It appears to be a mechanical switch of sorts mounted to the head just above the nozzle by a mm or 2....
View ArticleUsing X, Y and Z motor drivers as extra motors
Setup without XYZ motors.In a pick and place machine project I will use one board for XY and another without any XYZ motors.The free motor drivers would be setup as extra motors for special...
View ArticlePrusa i3 Mk2 Setup
Hi, I am trying to develop a new printing process for a university project using a prusa i3 mk2. I have been trying to change the Marlin firmware that came with the printer but have so far had no luck....
View ArticleDistortion correction to fix ROD LENGHT and PRINTER RADIUS
Hi, I recently bought a DIY Kit He3D K200 printer and after struggling through the worst-ensamble-videos-ever I manage to have everything up and running. Yesterday i finally could download the latest...
View ArticleXY Movement after limit switches
This is probably something simple, but I'm pretty hungup on it.I have an azteeg x3 pro, and I've been working on the firmware for a while, actually upgrading from an azteeg x3. At some point something...
View ArticleDetermining Z probe offset x & y
I am unconvinced that I understand the correct manner to determine z probe offset x, and z probe offset y. I've seen multiple write-ups that seem to use entirely different coordinate origins, and the...
View Articledistortion correction problem
Hi,Maybe I am doing something wrong but this is what's happening.First I use G32 S2 which puts the disitortion map in eeprom if I am right.When executing bed heigth map 3/4 of it is blue.By the way...
View ArticleXYZ max and min travel
I have three problems first is I need to know is there a way two have XY and Z axis set themselves to 0 after homing? My 2nd problem is when I turn on machine and host, it is at zero, I put in a G00...
View ArticleProblem compiling Repetier firmware in Arduino IDE
Hi,I am a newbie to 3D printers and have started making my second one. I have no professional education in electronics/mechanics/etc. I am an amateur and working this out as a part of my own project.I...
View ArticleDa Vinci Duo how do I change Filament Load/Unload carriage Location
Can anyone tell me where in the Repetier configuration file I can change the location of carriage when I am loading/unloading filament? I am working on an E3D Chimera upgrade for the Da Vinci 2.0...
View ArticleRoutine EEPROM writes
How often does 1.0.0dev "routinely" write to the chip eeprom? That is, updates to "total time active" -- "total filament used", etc.? Thanks.
View ArticleModifying the auto level dots matrix
Hello hope you are fineI currently have a Rostock mini with an inductive sensor and with the repeater firmware. I would like to know how I could modify the probing points to correct the undulations of...
View ArticleClik here to view.
Strange AutoLevel Behaviour
I had my reprap working great with the bltouch on the latest dev fw, no issues other than slicing and slightly loose x axis.Today, I setup repetier server on an old windows pc (just for testing before...
View Articlemigrating from stable to dev, xyz delta axis fail
Hi, first of all i would like to thank you all for the work you have put in to your software and firmware.I have been using the stable branch 0.92.x for a few months with no real issues apart from the...
View ArticleAutolevel on Delta leads to printing above bed
I have a home built delta printer which I'm trying to get working with Repetier firmware.I'm trying to get autoleveling to work with a Z probe actuated microswitch.Everything seems to be working...
View ArticleAuto-Leveling in Firmware Not Active - Mini IR Height Sensor
I have auto leveling enabled in firmware to use my mini ir height sensor board from David Crocker. I've followed directions from his blog https://miscsolutions.wordpress.com/mini-height-sensor-board/...
View Article