Clik here to view.
"Squashed" Prints after RAMPS from Melzi
Hello,I am a neophyte when it comes to the innards of firmware. I fried the Melzi in my Wanhao Duplicator i3. I was able to upload .92 to the a RAMPS 1.4 board. All is going well, aside from my...
View ArticleSpeed multipier vs. max feedrate
Hi,not shure if it ´s a bug or not.if i Change printspeed by host or ui i can set Speeds higher than max feedrate of machine.should´t that be prevented by Firmware?not shure where to prevent from...
View Articlediamond hot end extruder
i have a little problem .. when i try to move the filament with step motor t0, t1, t2 .. so turn all 3-step motor no matter what i do..and when i put it to t1. and writing the G92 E0 G1 E100 F2000 .....
View ArticleQuestions about dual X axis and Z2 end stop
If we got dual X axis,I think we should get two end stops for X axises , each for one axis,but I only found one,so how should we set up the end stop pin for both X axises？ And about the Z2 end...
View ArticleM106 commands with P0, P1, P2 etc addresses to the same print cooling fan,...
Liebe Kollegen, I have four fans in printer: one for extruder0, second for print cooling, third for motherboard, and last one is for enclosure ventilation (thermo coupled fan). After the print with...
View ArticleUltratronic pro v1 autoleveling
I can't seem to get the autoleveling feature to work on my ultratronics. The frimware I am using is repetier. The problem is that my printer will home, but when my z axis is homing, the x and y are...
View ArticleCore-XY: park the nozzle to another position after G28
Hi Roland, i've Core-XY with the Y endstop to the MAX position, and after the home I would like it not to remain in position 0 but go to a different value, in order to have the effector where I want,...
View ArticleJam detection immediate action
Good dayI use Jam detection for a filament runout sensor. JAM_ACTION 1If the filament runs out the printer will display the Jam detected message but will continue with the print that is still in the...
View ArticleHeated bed on and off too frequently
Dear Engineer, I'm using a relay to control the heated bed. I found a problem, for example, when I set the target bed temperature 50 °C, when the temperature arrived 50 °C, the relay switch off, and...
View ArticleAutoleveling with Ultratronics pro v1
Hi, I have got an incductive sensor and a min endstop for the Z-axis. How to I set up autoleveling to use my inductive sensor and my endstop for homing the Z-axis. Also, when I start the autoleveling...
View ArticleProblems with distortion correction - V1.0dev
Hello everyone,i'm running into strange problems while setting up my printer with the new 1.0 Firmware.I managed to get Autolevel working fine and tried to use the same coordinates for distortion...
View ArticleClik here to view.
Would you add a MKS MINI12864LCD
https://www.aliexpress.com/item/3d-Printer-Reprap-LCD-MKS-MINI12864LCD-mini-12864-Smart-Display-Controller-Full-Graphic-for-Mega-2560/32835858162.html?
View ArticleHelp with My Tevo Tornado
Hi I am a total newbie to 3D printing, I just received my new printer and put it together with out any issues But when i tried to print something nothing happened. I in seated the sd card, it said card...
View ArticleCan't start print "could not activate z"
I go to print a calibration cube on my tevo tarantula and after the bed and extruder are heated, everything is homed and is about to start I get the message "could not activate z" and it stops, please...
View ArticleQuestion about dual extruder
Hi , I build a machine like BCN3D sigma with dual X,EMy firmware version is 1.0.0 in Ramps-FD.I meet a problem and can't find why it happens.When I power on , connected with Repetier-Host.These are my...
View ArticleClik here to view.
Arduino Due will upload Repetier firmware from Arduino IDE but wont run on...
Hi there. I'd appreciate any help I can get as, right now I am at a loss.Vellemann K8200 Repetier firmware on a RADDS shield with the RADDS LCD controller installed.I had an Arduino Due clone board...
View Articlecould not activate Z probe error
i finally finished my new printer ready to go but I'm getting an error when bed leveling startscould not activate Z probe offset due to coordinates constraints result is inaccurateconfig as below//...
View Articleprinting mirrored Core XY
HiI egt all my printings mirrored. I can use the mirroring function within Repetier but it would be nice to have working as it should.How to easy change this?
View ArticleARDUINO IDE VERSION
Hello, Is there a specific ARDUINO version to compile and upload the firmware to an RUMBA board.I can compile and upload the firmware with the ARDUINO 1.0.1 version (without any error/warning message)I...
View Article