Second Heater Error - Not Heating Up
Hello, I have been having an issue with Repetier Firmware heating the second hotend on my printer. I am getting temperature feedback for both of them. Only the first hotend (T0) will work just fine...
View ArticleDavici Duo
Hello,i'am new here and my english is not the best. I hope you can understand my problem.I have download the Retier 0.92 for DaVinci 2.0Aby compiling there is an error message:Arduino: 1.5.8 (Windows...
View ArticleCannot run auto leveling then distortion correction
So what’s happening is if I run auto leveling it measures as planned and inserts z height as 284.387, then if I try and run distortion correction it give error of unreachable cycle probing of 4.00056,...
View Articledual x axis
Hi all , i would like to implement my second extruder to an indipendent x axis. i've seen that it is possible to configure in repetier firmware config tool "dual x axis" and link it to the Extruder E2...
View ArticleIs it possible/meaningful to use distortion correction without rotation...
Gruess Gott! I've got printer with Prusa-like kinematic, mechanic probe with optical endstop (BLtouch self made). I print on not very flat glass. The maximum bed height distortion is 0.2 mm. In the...
View ArticleClik here to view.
Repetier firmware driver timings
hi, so, it happens that i have an SKR 1.3 which unfortunately is not supported by repetier so i had to resort to marlin or reprapfirmware.what i noticed however, is that going from repetier (ramps) to...
View ArticleProblem in controlling 3D printer via smart display controller
I am using 12864 LCD with full graphic Smart display Controller for controlling the printer without laptop. How do I Change the sensitivity of the potentiometer controlling the movement of X, Y, Z...
View ArticleRepetier firmware on Tronxy X5SA-400
Hello!I am kind of new to 3d printing and not a 100% sure on basically anything yet but I have been trying to use Simplify3D for almost a month, creating my own printer profiles but also getting...
View Articlefustrated with online Repetier configurator
I have been trying to compile version .92 of Repetier for a Melzi board for 3 weeks now with no success. The online configurator is very confusing to me. Can someone provide the configuration.h file...
View ArticleI need help about menu on 12864 display
Right upper part of the display where coordinates are displayed is shited to the left....wrong position.....about 10 pixels to the left.Where i can change this positioning in configuration files?
View ArticleFeeds slower than F300 (mm/min) are not respected
I have a Monoprice Maker Select which reports that it is running Repetier 0.91. I'm sure this is quite old, and that upgrading is probably the fix for this. Nevertheless, I wanted to see if anyone is...
View ArticleDual Z steppers and dual extruder
My machine is a home built cartesian using AtMega 2560 and Ramps1.4 board and dual extruders into a Y/ E3D hotend. Was using Marlin until I upgraded to dual Z steppers and a BLTouch (sadly my second...
View ArticleWhere Can You Purchase CBD Oil In Michigan?
Hemp oil can confer with a full-spectrum oil from the Cannabis sativa plant or hemp seed oil, which is oil that comes from just the seeds of the hemp plant. The bottom line is that extra clinical...
View ArticleX/Y Achse fährt nach Reste in die falsche Richtung
HalloIch habe ein Problem mit den X und Y Achsen. Nach jedem Reset, Motor aus oder Neustart reagieren sie nicht richtig. Wenn ich sie Manuel bewege geschieht manchmal gar nichts, teilweise geht es in...
View Article500mg & 1500mg Power
CBD oil has grow to be extremely popular over the last few years, so you've probably heard how it's probably the most potent anti-inflammatories around, how it can reliably cut back anxiety, and even...
View ArticleTopical CBD Ointment
Get The Purest CBD Oil On-line in Canada. cbd gummies for sleep and anxiety be an issue besides that on the federal level doctors are legally prohibited from prescribing cannabis. The Grow-Off starts...
View ArticleTMC 5160 Support
Hello !Is there any support for TMC 5160 in repetier firmware ?As the two steppers seems to be very close in configuration, can we use it or not and if not, when ?Thanks
View ArticleHeater decoupled notification
Hi,I am using:Repetier Firmware 1.0.3devRepetier Server Pro 0.91.2Printer CR-10S with E3D Titan AeroAfter a few hours of printing I get a heater decoupled notification and the printer stops.Is there a...
View ArticleCBD Isolate Or Full Spectrum CBD
When purchasing for CBD , you've in all probability come across merchandise labeled as full spectrum, broad spectrum, or CBD isolate. No matter happens on the farming side, the passage of HB-171 can be...
View ArticleTMC 5160 Support
Hello !Is there any support for TMC 5160 in repetier firmware ?As the two steppers seems to be very close in configuration, can we use it or not and if not, when ?Thanks
View Article